How long does Hilti 500 take to cure?
Hilti HIT-RE 500 V3 is the only epoxy adhesive anchor that cures below freezing and is rated down to 23o F. Balance longer work times with shorter cure times. Hilti HIT-RE 500 V3 gives you a 25-minute working time at 72o with initial cure in four hours and full cure in six hours.
Can you use Hilti epoxy in the rain?
Hilti Verified Yes, a wet hole can affect the performance of post-installed adhesive anchors.
What Hilti 500?
Fifteen years ago, Hilti set legendary standards for designers and contractors with the HIT-RE 500 – the first epoxy injectable mortar for post-installed anchors and rebar fixings. And because our customers needed the same high performance and maximum reliability for cracked concrete, we introduced HIT-RE 500-SD.
Will Hilti epoxy set up in water?
Hilti Verified Hilti’s HIT-RE 500 V3 adhesive anchor system has approvals for submerged (underwater) conditions, however, HIT-HY 200 does not. Therefore, you might want to consider using HIT-RE 500 V3 for your application.
Does Hilti epoxy expire?
It’s likely fine, I haven’t used that particular type of epoxy before, it would be worth a call to your local hilti rep for a second opinion. That is definitely the expiration. Expiration is usually about 2 years after manufacture, so your product is over double the shelf life. On a job site it would be rejected.
Can Hilti epoxy freeze?
First of all, do not despair, frozen epoxy isn’t ruined! Although both your resin and activator are capable of freezing, it’s very easy to return them to a usable liquid state.
What is the difference between Hilti 200a and 200r?
Hilti HIT-HY 200-A will have shorter working times and curing times than Hilti HIT-HY 200-R. The user can select product gel time suitability based on temperature of the base material and jobsite time requirements. The packaging for each is different which helps the user distinguish between the two adhesives.
Will concrete anchors work on asphalt?
Asphalt and concrete have one property in common — you can drive on either of them. But when it comes to attaching anything to asphalt, anchoring has nothing in common with concrete. The difficulty with anchoring to asphalt is that it will yield, over time, to continuous pressure.
What is submerged application?
There is a cooling water tower basin that need to use a post-installed anchor. On anchor selection guide of the Hilti Technical Guide, we have to use a HIT RE-500 V3 for submerged installation. When we install an epoxy anchor in the basin, there will be in water-saturated concrete condition.
What is a chemical anchor?
Chemical anchoring is a technique for fastening to concrete and similar substrates that provides more flexibility than mechanical anchoring. A mechanical anchor, such as a sleeve anchor, Dynabolt®, wedge anchor or drop-in anchor, is inserted in the concrete and expands upon tightening.
What is Hilti hit-re 500 with rebar?
Hilti HIT-RE 500 with rebar in hammer drilled holes jection mortar syste Hilti HIT-RE 500 330 ml foil pack (also avai able as 500 ml and 1400 ml foil pack) Statik mixer rebar S Benefits – suitable for non-cracked concrete C 20/25 to C 50/60 – high loading capacity – suitable for dry and water saturated concrete
What are the safety factors of the Hilti hit-re 500-sd?
The partial safety factors for action depend on the type of loading and shall be taken from national regulations. Hilti HIT-RE 500-SD with HIS-(R)N 10 / 2012 409 Design resistance: concrete C 20/25 – f ck,cube= 25 N/mm², Temperature range I Data according ETA-07/0260, issue 2009-01-12 Anchor size M8 M10 M12 M16 M20 Embedment depth h
How long does Hilti hit-re 500 V3 take to cure?
Hilti HIT-RE 500 V3 is the only epoxy adhesive anchor that cures below freezing and is rated down to 23 o F. Balance longer work times with shorter cure times. Hilti HIT-RE 500 V3 gives you a 25-minute working time at 72 o with initial cure in four hours and full cure in six hours.
What is the design resistance of hit-re 500-sd with hit-V Rod?
Hilti HIT-RE 500-SD with HIT-V rod 10 / 2012 394 Design resistance: concrete C 20/25 – f ck,cube= 25 N/mm², Temperature range I (load values are valid for single anchor) Data according ETA-07/0260, issue 2009-01-12 Anchor size M8 M10 M12 M16 M20 M24 M27 M30 Embedment depth h