What does a PhosBan Reactor 150 do?
The PhosBan Reactor 150 is designed with the upflow principle to achieve the most efficient use of PhosBan or other chemical filter media. By pushing water from the bottom upward through a dispersion plate, it forces an even distribution of water through the media, and prevents channeling.
What do Biopellets do in reef tank?
Biopellets are made from pure biodegradable plastic. When added to your aquarium in a biopellet reactor, the pellets act as a carbon source for bacteria. In essence, the pellets are food for bacteria.
What does a Biopellet reactor do?
The pellets are made of a biodegradable polymer. As the polymer breaks down, carbon is slowly released for the bacteria. This stimulates the nitrate-removing bacteria to do their job. The reactor allows you to control the water flow through the biopellets, safely maximizing the nitrate removal in your aquarium.
How do you open a Phosban reactor 150?
Open reactor lid by turning counter clockwise. Check parts list to confirm that all parts are present. The reactor is supplied with all the parts needed to operate it except for the hose and pump.
What is a reactor for aquarium?
A media reactor is an aquarium filtration device that contains filter media. It helps to increase the effectiveness of the filter media inside by forcing all water that enters the reactor to come in contact with the media.
Is Phosguard the same as Gfo?
They’re similar, but Phosguard is aluminum oxide and depletes rather quickly compared to gfo (Depending on how much phosphate is being removed, of course) and can release phosphate back into the water when exhausted (Unlike gfo.)
When should I change my Biopellets?
Future Maintenance. Depending on the system add new Biopellets every 6-12 months. Do not remove remaining biopellets.
How much flow for Biopellets?
1. Measure Biopellets. Add one cup (236mL) of BRS Biopellets per 50 gallons of system water volume to the reactor. For example, a 100 gallon tank would require 2 cups of BRS Biopellets.
How do you use RowaPhos in a reactor?
Place the product between two layers of filter wool in a canister filter. Do not sprinkle into the your reef tank. RowaPhos recommends that you use a small quantity and replace regularly rather than a large amount and replace infrequently.
What is the capacity of a phosban 150 reactor?
Operating Instructions for the PhosBan Reactor 150 ™ Technical Data Capacity Use with up to a maximum of 200 grams (385 ml) of PhosBan, or a media height of 5 inches (13 cm). Aquarium size One reactor for up to 150 gallons (568 Liters). Multiple reactors may be used for larger aquariums.
How much phosban can I put in my Aquarium?
Technical Data Capacity Use with up to a maximum of 200 grams (385 ml) of PhosBan, or a media height of 5 inches (13 cm). Aquarium size One reactor for up to 150 gallons (568 Liters). Multiple reactors may be used for larger aquariums. Recommended flow rate ca. 20 – 30 gal/hr (75 – 115 l/hr).
Can I use a media bag in the phosban reactor?
Important Notes: Do not use a media bag in the PhosBan Reactor. Simply place PhosBan or other GFO media inside it according to the instructions. Don’tover or under fill the column. Max 5 in (13 cm) of GFO media, min 2 in (5 cm). When using only activated carbon, the entire column can be filled.
How do you install a phosban reactor?
2. Locating the reactor The PhosBan reactor can be seated upright in the cabinet, in the filter sump, upright on the floor below the aquarium or hanging on the side or rear of an aquarium. For hanging installations, use threaded bolt provided in the base plate to level it against the aquarium wall.